LEARN MORE ABOUT OUR EQUIPMENT FITMENT GUIDE IN THE VIDEO BELOW!
- Dahlgren Decon™ is a three-component decontamination solution that can quickly decontaminate most chemical warfare agents, toxic materials, and other emerging threats. In testing conducted by the U.S. Department of Defense and other federal agencies, Dahlgren Decon has been found to be the most effective and fastest reacting decontaminant on the mark.
- My most recent retrofit is an old Dahlgren System 300z. The guy dropped it off at my house for $100. It's a 3-axis engraver with a work area of 12' x 24' x 4.5'. It sure isn't pretty and it hasn't been used in 10 years but not bad for being delivered to my house for $100. It's built heavy and the rails are all in good condition.
Dahlgren, VA. Video Teleconference Technician. Dahlgren, VA. 48 minutes ago. Oshin theme song mp3 free download. Vessel Master (100 Ton). Technical Manual Support Services Contract. Port Hueneme, CA. Organization Development Specialist III. Final fantasy x iso download. Unmanned & Expeditionary Weapon Systems Contract. Dahlgren, VA. 30+ days ago. Program Analyst. Dahlgren, VA.
CALL TODAY! 1-888-541-0613
Follow and Like us on Facebook: Engraving Machines Direct, Inc
Featured Machines
(2)
MSRP: $10,995.00
(0)
MSRP: $13,995.00
(29)
MSRP: $5,995.00
(16)
MSRP: $3,995.00
(0)
MSRP: $12,995.00
(3)
MSRP: $4,995.00
(0)
MSRP: $12,995.00
(0)
MSRP: $6,495.00
(0)
MSRP: $16,995.00
(0)
MSRP: $13,995.00
(0)
MSRP: $4,400.00
(0)
MSRP: $2,250.00
(0)
MSRP: $900.00
(0)
MSRP: Starting from $650 - $1,100
(0)
MSRP: Starting from $900 - $1,500
(0)
(0)
MSRP: Call for Monthly Special!!
Dahlgren System 300 Manual Download
(0)
MSRP: Call for Monthly Special!!
(0)
Dahlgren System 300 Manual Pdf
MSRP: Call for Monthly Special!!
(1)
MSRP: $6,995.00
(0)
Dahlgren System 300 Manual 2017
MSRP: $1,040.25
(0)
(0)
MSRP: $525.00
(0)
MSRP: $6,995.00
(1)
MSRP: $6,995.00
My most recent retrofit is an old Dahlgren System 300z. The guy dropped it off at my house for $100. It's a 3-axis engraver with a work area of 12' x 24' x 4.5'. Adobe photoshop 7.0 free for mac pro.
Landlordmax support. It sure isn't pretty and it hasn't been used in 10 years but not bad for being delivered to my house for $100. It's built heavy and the rails are all in good condition.
The old controller box box is rated for 500w with an intel 8086 and 65k of ram. It has separate cards for each motor driver and the spindle. The motherboard is labeled 65v and the components are rated for 100v. I'll be replacing all this with some more modern drivers and creating a custom controller for it.
Each axis, the spindle, and limit switches are nicely separated with plugs for each.
The stepper motors are Powermax P22NRX8 unipoler steppers with a rating of 3.3A.
I'm unsure of the spindle motor at this point but know it's a 3 phase BLDC motor with hall sensors for feedback after doing some tracing of the pins on the driver card.
I got it working:
Some more over at my blog www.codelv.com/blog/search/?q=engraver